A Beginner's Guide to Installing a Bathtub
A Beginner's Guide to Installing a Bathtub
Blog Article
What are your thoughts and feelings about Installing A Bathtub?
Setting up a tub isn't precisely brain surgery, however it does require solid plumbing, woodworking, and also in some cases, tiling abilities. Changing an old tub with a new one is additionally a moderately challenging project. If the old bathtub is easily easily accessible, the project can relocate easily; if you have to open up a wall surface to remove the old bathtub and place the new tub, the job is much harder. In either instance, the project is within a residence handyman's skills, although you will require a helper to leave the old bathtub and embeded in the brand-new one. Ensure you have actually certified yourself for the task as well as fit attempting it. Instead of hiring a service provider to take over a halfway-completed task, it is far better to think about using one before you begin. Chances are you might require an expert plumber to make tube links.
This post will certainly assist you mount a new tub in your bathroom if you have actually currently purchased a brand-new bathtub and do not require to change the plan of your previous water pipes.
Your tools as well as product list should make up the following:
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your setup, after that the first thing you should do is disconnect the water. After doing so, turn on the taps to drain pipes any kind of water staying in the system. The process of getting rid of the existing taps can be rather troublesome as a result of the limited gain access to that is often the situation.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the taps. Have a cloth ready for the staying water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary faucets from turning during this procedure. When the taps have been removed, the holes in the bath/basin will have to be cleansed of any old sealing substance.
Before proceeding to fit the new faucets, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new faucets to fit.
Suitable New Touches
If the tails of the new taps are plastic, after that you will require a plastic port to avoid damages to the string. One end of the connector fits on the plastic tail of the faucet as well as the other end provides a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will need reducing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, place the tap in the mounting hole in the bath/basin making sure that the washing machines remain in place between the faucet and also the sink. Secure the tap in place with the manufacturer supplied backnut. Once the tap is firmly in position, the supply pipelines can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with normal faucet adapters. The previous kind should be connected to the tap ends first, tightening only by hand. The supply pipelines can later be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Setting up the Tub
Making use of both wood boards under its feet, put the bathtub in the required placement. The wooden boards are useful in equally spreading out the weight of the tub over the location of the boards instead of concentrating all the weight onto four little factors.
The next objective is to make sure that the bath tub is leveled all round. This can be achieved by examining the level and changing the feet on the bath tub till the spirit level reviews degree.
To set up taps, fit all-time low of the furthest flexible tap adapter to the appropriate supply pipe by making a compression join; then do the exact same for the other tap.
Switch on the water system as well as inspect all joints as well as new pipework for leaks and also tighten them if required. Fill the bathtub and also check the overflow electrical outlet as well as the typical outlet for leakages.
Lastly, repair the bathroom paneling as explained in the producer's user's manual. Tiling as well as sealing around the bath tub ought to wait till the tub has actually been utilized at least once as this will certainly resolve it into its final placement.
Getting ready for the Installation
To start with, the sustaining structure provided with the bath must be fitted (if called for) according to the maker's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is important to ensure that if the tap comes with a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the faucets unit to stop pressure on the bath tub.
Fit the flexible faucet ports to the bottom of both faucets utilizing 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you use all of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath must now be ready to be fitted in its final position.
Tiling Around the Bath tub
In the location where the bathroom satisfies the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to crack a rigid seal, triggering the water to penetrate the wall surface in between the bathroom as well as the tiling, bring about issues with wetness as well as possible leakages to the ceiling below.
You can select from a selection of coloured sealants to blend in your components and fittings. They are offered in tubes and also cartridges, and are capable of securing voids approximately a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of drenched paper or soft rope. Remember to always fill up the tub with water before securing, to enable the activity experienced when the bathtub remains in usage. The sealer can fracture rather very early if you do not take into account this movement prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise conveniently readily available on the market. It is advisable to fit the tiles using water-resistant or waterproof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you appreciate more info about How to Install a Bathtub? Put feedback further down. We would be delighted to listen to your opinions about this piece. We hope that you visit us again soon. Are you aware of somebody who is excited by the topic? Feel free to promote it. We treasure reading our article about How to Install a Bathtub Yourself.
Quick, quality, call! Report this page